[Rhenderson]

What all to i need to look into to getting my b16a for running a nice na setup??

 

[FNEG]

ask spoolie i think he has the most supercharger knowledge for hondas on this site

 

[daegg]

all u need to do is make sure u oil your btek realy good and your ready for the boost

 

[do it sideways]

vortec makes a badass supercharger for b16a2. im guessin it'd fit 1st generation too?

 

[Rhenderson]

all u need to do is make sure u oil your btek realy good and your ready for the boost

well i oiled my btek today and it turned out pretty nicely...lots of high end power...lol

 

[Ventolin]

What supercharger are you wanting to run? Don't expect much. I've got a JRSC, but the only reason I bought one was because I got it very cheap.

If you're not going to run the FMU, which I wouldn't, on any system you'll need a Walbro, injectors, and Hondata or some other form of engine management. Then you'll need it tuned.

The Procharger, Vortech, or JRSC kit can all be run on a stock motor, just don't expect much.

 

[jcoosi]

How much hp are you looking to make?

 

[Rhenderson]

im just looking for something moderatley cheap and reliable....and just looking for a fully built engine eventually just trying to figure out what brands and stuff to go with..

 

[jcoosi]

How much hp are you looking to make?

 

[Rhenderson]

How much hp are you looking to make?

not really looking to make any set amount of hp. but I would prob hope for somewhere around 250 a guess or more.

 

[FNEG]

How much hp are you looking to make?

not really looking to make any set amount of hp. but I would prob hope for somewhere around 250 a guess or more.

good luck

 

[CiviclyDumped]

superchargers are cool but if you want to make that 250 hp easier then i would turbo the car. and its easier to make more power if you ever wanted.

 

[jcoosi]

How much hp are you looking to make?

not really looking to make any set amount of hp. but I would prob hope for somewhere around 250 a guess or more.

Need to run a compression test and leak down test on the eng if all checks good then its a go.You can do 350 on stock bottom ends safely.The b16 heads can support 500 with no work done to them.If you want to go over 350hp look into some Manley rods and cp pistons.I listed these because they are what I use and have had no problems.You will need some type of eng management ie Hondata,AEM,ectune or Neptune.You will need a set of 440 or 550 injectors RCs injectors are a good brand.You will need a 255lph walbro fuel pump.Forced00si made 300+ on his vortech setup.For a bolt on kit either go Vortech or Procharger.

I would recommend a set of valve springs and if you are wanting a set of cams stick a set of gsr camshafts in it.Also look into a good header and some 2.5 inch exhaust.

 

[Rhenderson]

ok thanks for the help...where can i get a compression test done at?

 

[CiviclyDumped]

ok thanks for the help...where can i get a compression test done at?

you can buy the tool to do it yourself at advance auto parts for like 20 bucks or so

 

[Rhenderson]

i think ill just gonna go all motor for now..

 

[spoolie]

i think ill just gonna go all motor for now..

then i would just keep it stock then....

 

[Rhenderson]

well if you wanna give me a supercharger that would be fine..lol

 

[spoolie]

everything is for sale...

 

[Tetro]

even your soul? ^