Joined
·
359 Posts
Updated 6/3/2019
Looking for a new eshaft. The original one is out of alignment, and in such a way that it cannot be straightened. This will not effect it's use, but the RPM limit has been limited to 8500 RPMs by Rick Engman. That doesn't work for the NA plans, so I need to find a new one.
Goal 450WHP
Mazmart
B series motor purchased. Reliable source, and on the shelf.
Iron lapping
Built by Myles Fisher
Large Street Port, and semi pport
OE Seal kit
17pc Goopy 10mm stud kit
I-Rotay apex seals
Chip Motorsports
Rotor lightning, clearancing, and balancing 20b rotors
GOing to have to do the 9.7 rotors now... lightning, balance, scallop, and clearance.
Billet oil pan
Fabrication by Coffee Fabrication
Flaming River custom steering rack. Little faster ratio than stock
MK3 MR2 Electric power steering pump - eventually. May end up doing it myself.
370z transmission mounting.
Reverse mounted hood to open to the front - eventually
Drive-train / Engine Parts
Xcessive Engineering Short LIM
6x ID 1050 injectors
Adaptronic plug and play ECU
20b crossmember from Promaz
370z JK40C Transmission
Body
2012 Spirit R head lights
Autoexe Type C hood (Will be replaced with a one off hood by MPH Fabrication)
Autoexe duck-tail trunk
Leg Motorsports RX Vision front bumper (Being remolded by MPH Fabrication into dry carbon with carbon zylon inserts)
Lions Kit S2 over fenders - will replace with metal eventually.
Marsh Powerhouse Fabrication carbon zylon roof
RE Amamiya carbon tail lights
RE Amamiya AD Pro fender mirrors
Vertex Lang rear bumper
Vertex Lang side skirts (May change)
Misc Parts
Autoexe big brake kit
Autoexe S1 steering wheel
Autoexe ball type shift knob
90's Mazda Speed seats
Volk SF Challenge wheels
Looking for a new eshaft. The original one is out of alignment, and in such a way that it cannot be straightened. This will not effect it's use, but the RPM limit has been limited to 8500 RPMs by Rick Engman. That doesn't work for the NA plans, so I need to find a new one.
Goal 450WHP
Mazmart
B series motor purchased. Reliable source, and on the shelf.
Iron lapping
Built by Myles Fisher
Large Street Port, and semi pport
OE Seal kit
17pc Goopy 10mm stud kit
I-Rotay apex seals
Chip Motorsports
Rotor lightning, clearancing, and balancing 20b rotors
GOing to have to do the 9.7 rotors now... lightning, balance, scallop, and clearance.
Billet oil pan
Fabrication by Coffee Fabrication
Flaming River custom steering rack. Little faster ratio than stock
MK3 MR2 Electric power steering pump - eventually. May end up doing it myself.
370z transmission mounting.
Reverse mounted hood to open to the front - eventually
Drive-train / Engine Parts
Xcessive Engineering Short LIM
6x ID 1050 injectors
Adaptronic plug and play ECU
20b crossmember from Promaz
370z JK40C Transmission
Body
2012 Spirit R head lights
Autoexe Type C hood (Will be replaced with a one off hood by MPH Fabrication)
Autoexe duck-tail trunk
Leg Motorsports RX Vision front bumper (Being remolded by MPH Fabrication into dry carbon with carbon zylon inserts)
Lions Kit S2 over fenders - will replace with metal eventually.
Marsh Powerhouse Fabrication carbon zylon roof
RE Amamiya carbon tail lights
RE Amamiya AD Pro fender mirrors
Vertex Lang rear bumper
Vertex Lang side skirts (May change)
Misc Parts
Autoexe big brake kit
Autoexe S1 steering wheel
Autoexe ball type shift knob
90's Mazda Speed seats
Volk SF Challenge wheels
